|
Back to menu |
|
|
Splicing Connectors and Termination Accessories |
 |
PWSC Splicing Connector, 2
Point
Used when splicing
standard 2 conductor Protectowire Linear Heat
Detector.
Material: Nylon
Screw Turret: 1/8 inch |
 |
 |
PWSC-3 Splicing Connector,
3 Point
Used when splicing
standard 3 conductor Protectowire Tri-Wire
Linear Heat Detector.
Material: Nylon
Screw Turret: 1/8 inch |
|
|
 |
PWS Splicing Sleeves
Used when splicing any
Protectowire Linear Heat Detector.
Material: Copper |
|
|
 |
PFL Flexible Leads
Used when terminating 2
conductor Protectowire Linear Heat Detector in
constrained spaces such as pull station or smoke
detector back boxes.
Material: Copper splice
sleeve, 24 AWG tinned copper lead, PVC
insulation
Click
here for
detail. |
|
|
 |
SR-502 Junction Box Sealed
Strain Relief
Used when Protectowire
Linear Heat Detector penetrates junction and
end-line boxes. Water and Oil resistant.
Material: Aluminum Cast
Housing, rubber seal and O-ring.
Click
here
for detail. |
|
|
 |
SFTS-1-8-F Sealant Tape
Used to seal all splices
of Protectowire Linear Heat Detector against
moisture. |
|
|
 |
#35 Splicing Tape,
Available in White, Red and Blue
Used to protect all
splices of Protectowire Linear Heat Detector
after sealing against moisture using SFTS-1-8-F
Sealant Tape. |
|
|
 |
33+ Low Temperature
Splicing Tape, Black
Used to protect all
splices of Protectowire Linear Heat Detector
after sealing against moisture using SFTS-1-8-F
Sealant Tape in cold environments. |
|
|
 |
SU-15 Wire Dispensing Reel
Used to dispense coils of
Protectowire Linear Heat Detector during
installation.
Material: Steel Fabricated |
|
Back to menu |
|
|
General Purpose Fastenders |
|
 |
WAW Clips, Type N and P
WAW Clips may be used for
ceiling or wall mount applications, as well as
at corners. The fastener is a clip which wraps
around the Detector and is available in either
nylon (WAW-N) or polypropylene (WAW-P) material
depending upon the installation environment. As
a general rule, nylon WAW-N's are preferred for
applications where the ambient temperature is
expected to be low such as freezer warehouses.
The installation temperature range for the WAW
Series fasteners is -40°F (40°C) to 190°F
(88°C).
Click
here for detail. |
|
|
 |
OHS Clips, Type 1 and SS
OHS clips are available in
several different configurations and are used
mainly as an intermediate fastener between
corner mounted WAW clips which provide the main
support.
OHS-1 - Galvanized Steel, 3/16" (4.8mm) diameter
mounting hole
OHS-SS - 304 Stainless Steel, 1/4" (6.4mm)
diameter mounting hole |
|
|
 |
BC-2 Beam Clamp
The BC Series Beam Clamp
Assembly, consists of a beam clamp, WAW clip and
snap button. BC-2 utilizes a plated steel clamp
and is recommended for general indoor use. These
versatile fasteners may be used for mounting
Protectowire on cable trays, conveyors, angle
irons, I-beams, bar joists, etc.
Click
here for detail. |
|
|
 |
BC-3 Beam Clamp, Type N and P
The BC Series Beam Clamp
Assembly, consists of a beam clamp, Nylon WAW
clip (type N) or a Polypropylene WAW clip (type
P) and snap button. the BC-3 utilizes a heavy
duty zinc plated clamp suitable for both indoor
and outdoor use. These versatile fasteners may
be used for mounting Protectowire on cable
trays, conveyors, angle irons, I-beams, bar
joists, etc.
Click
here for detail. |
|
|
 |
RMC L-Bracket, Type 2 and 3
The RMC Series L-bracket
consist of a steel bracket, WAW Clip and snap
button and are often used for mounting
Protectowire to the rim seals on floating roof
tanks. The brackets are 6.7 inches (17.0 cm)
long and contain five mounting holes which allow
for multiple height adjustments of the
Detector’s installation position. The brackets
are available in plated steel (type 2) or
stainless steel (type 3) models, and may be used
in a wide variety of common installations and
applications.
Click
here for detail. |
|
|
 |
TR-5G, Insulated Standoff
The TR-5G Insulated
Standoff can be used to install Protectowire on
or above coal conveyors or from other applicable
mechanical structures.
The standoffs may be installed through
holes in covers or brackets by means of the
1/4-20 locknuts provided. In another type of
installation, the standoffs may be connected to
threaded rods suspended from the ceiling by
means of coupling nuts (not provided). Since
this fastener does not grasp the Detector
tightly, it is necessary to use other fasteners
such as WAW clips to place sufficient tension on
the Protectowire to prevent it from drooping.
|
|
|
 |
EMS-A-CO Adhesive Cable Mount
Used when drilling into
mounting surface is not possible or prohibited
such as transformer surfaces. Adhesive mounting
system consists of EMS cable mounts, PLT cable
ties and approved industrial adhesive.
Constructed of black weather resistant nylon and
suitable for outdoor use when used with approved
adhesive. Should not be used in chemically harsh
environments or areas where temperatures are
less than 0°F (-17°C) or exceed 180°F (82°C).
Click
here for detail. |
|
|
 |
PLT1S-CO Cable Ties for Cable
Mount
Used with EMS Cable
Mounts, constructed of weather resistant nylon
suitable for outdoor use. |
|
|
 |
SIKAFLEX-291, Industrial
Adhesive
Used with EMS Cable
Mounts, Should not be used in chemically harsh
environments or areas where temperatures are
less than 0°F (-17°C) or exceed 180°F (82°C).
Tack Free Time: 60 minutes, Rate of Cure: 0.25"
(6.35mm) x 0.25" (6.35mm) bead 4 days at 74°F
(23°C) / 50% relative humidity. |
|
Back to menu |
|
|
Cable Tray
Application Fasteners |
 |
HPC-2, Spring Clip
This single piece UV
resistant nylon clip consists of a special
snap-lock design, which allows for easy
installation or removal of the Protectowire
Linear Heat Detector from the fastener. The
HPC-2 contains an internal spring steel drive
clamp with gripping teeth that will accommodate
mounting surfaces from .06 to .25 inches (1.5 -
6.4 mm) thick, making the clip suitable for a
wide range of applications such as cable trays,
storage racks, and ceiling joists.
Click
here for
detail. Use your browsers Back to return to this
page. |
|
|
 |
CC-2N and CC-2W, Cable
Tray Clip
These cable tray clips
consist of a “Caddy” style steel clamp, WAW, and
snap button. They are designed to attach to the
cable tray side rails and secure the
Protectowire in the recommended sine wave
pattern.
The clips are available in two models, each
designed to accommodate different material
thickness. Model CC-2N will clamp to material
from .06 to .16 of an inch (1.6 - 4.0 mm) thick.
Model CC-2W is designed for material ranging
from .16 to .25 of an inch (4.0 - 6.4 mm) thick.
Click
here for
detail. Use your browsers Back to return to this
page. |
|
|
 |
CC-10N, CC-10W Cable Tray
Clip
The CC-10 Series Clips,
are similar in concept to the CC-2’s, but
utilize a different “Caddy” style drive clamp.
The CC-10’s will accommodate material thickness
of up to .50 inch (12.7 mm) and also provide a
means of locking the fastener in place by using
one of the threaded mounting holes. The CC-10N
is designed for material ranging from .13 to .25
of an inch (3.2 - 6.4 mm) thick. The CC-10W will
clamp to material from .31 to .50 of an inch
(7.9 - 12.7 mm) thick. By adding the suffix “-S”
to the above model numbers, the fasteners are
provided with a 1/4-20 hex nut and 3/4 x1/4-20
hex screw which are designed to securely hold
the clamp to the mounting surface. These clamps
are particularly useful in applications where
excessive vibration may be encountered.
Click
here for
detail. Use your browsers Back to return to this
page. |
|
Back to menu |
|
|
Pipe Mounting Application
Fasteners |
 |
PM-3A Series Pipe Straps
These double loop straps
suitable for .75" to 2" pipe are made of black
weather resistant 6/6 Nylon and may be used in
temperatures ranging from -40°F (-40°C) to 185°F
(85°C).
Click
here for
detail. |
|
|
 |
PM-3B Series Pipe Straps
These double loop straps
suitable for 2.5" to 3.5" pipe are made of black
weather resistant 6/6 Nylon and may be used in
temperatures ranging from -40°F (-40°C) to 185°F
(85°C).
Click
here for
detail. |
|
|
 |
PM-3C Series Pipe Straps
These 2 single loop straps
suitable for 4" to 6" are made of black weather
resistant 6/6 Nylon and may be used in
temperatures ranging from -40°F (-40°C) to 185°F
(85°C).
Click
here for
detail. |
|
Back to menu |
|
|
Messenger Wire Fasteners |
|
Messenger wire (a Protectowire exclusive), is
available with any model Detector on special
order. It consists of high tensile strength
stainless steel wire, which is wound around the
Detector at the rate of approximately one turn
per foot (.3 m). It is a carrier or support wire
which is designed to simplify the installation
of the Detector in areas where mounting is
difficult due to the lack of appropriate support
structures or mounting surfaces. When using
messenger wire to support the Detector,
turnbuckles and eyebolts must be employed at
each end of a straight run to place tension on
the support wire. Click
here for
detail. Use your browsers Back to return to this
page. |
 |
TR-4A, TR-4A-S, Eyebolt
Use to attach one end of
messenger wire to supporting structure. TR-4A
steel construction, TR-4A-S stainless steel
construction. |
|
|
 |
TR-24, TR-24-S, Turnbuckle
Use to attach and tension
one end of messenger wire to supporting
structure. TR-24A steel construction with
aluminum casing, TR-24A-S stainless steel
construction with aluminum casing.
|
|
Back to menu |
|
|
Service &
Troubleshooting Tools |
 |
APL-90 - Alarm Point
Location Meter Adapter. Converts almost any
Digital Multimeter into an alarm point location
meter. Allows the general actuated (shorted)
area of Protectowire LHD to be located by
displaying a distance reading in Feet (Optional
Meters) to the actuated point. |
|
|
 |
MFL-92 - Manual Fault Locator System.
Allows an actuated (shorted) point of
Protectowire LHD to be accurately located.
A signal generator is connected across the
Protectowire LHD. A receiver then monitors the
signal by tracing along the Protectowire run
with a pick up. The audible signal is lost at
and beyond the actuated point. |
| |
